
Sponsors and partners
Put your brand
on our drift car.
A fabrication shop with its own drift car. Four brands already back it, and there's room for yours.
Partners
Our sponsors
These brands back our drift program. Your logo could sit alongside them.
About
Who you're backing
Ondoors is a custom fabrication shop with its own drift car. We make intercooler piping, catch cans, tanks and airboxes for other people's cars, and we built our own car the same way.
We've been drifting since 2019 and stepped up to competition in 2026. The program is growing, so partners who come in now get a prominent spot on the car, not a corner of a crowded one.
- Drifting since
- 2019
- The car
- R31 wagon, LS1
- Built
- In our shop
- Partners
- 4


What partners get
What a partnership includes

Your brand on the car
Your logo on the R31, at events and in every photo and video of it. Placement is worked out with each partner.
Social posts and videos
Mentions in our posts and videos: builds, fab work and event days. Once our YouTube channel is up, you're in that too.
Passenger laps
Ride-along laps in the car for sponsors. The best way to see what you're backing.
Represented properly
We look after the brands that look after us: at events, in the pits and online, we talk about your gear honestly and put it in front of the people who use it.
Every partnership is put together to suit the brand. Tell us what you want out of it and we'll work out what fits.
The car and the driver
The R31 wagon
Built in our shop with help from friends and family: most of the paint was done in the family, and the bash bars are by Gregory's Kustoms.
For the fab side, every build we've done is in the portfolio.
- The car
- R31 Skyline wagon, LS1 V8. Built in our own shop from 2022, finished in 2024.
- Home base
- Douglas Park, NSW
- Where it runs
- Sydney Motorsport Park (Eastern Creek), North and South circuits, since 2024
- Australian Drift Club days
- Local drift days
- Competition
- VicDrift Championship 2026: first competition round, entered to build comp experience.
The full build sheetLS1 · T56 · Haltech · full spool
Engine
- LS1 V8 swap, stock internals
- Melling high-flow oil pump, dual-row timing chain
- 25% underdrive kit
- Holley Sniper low-profile intake manifold and fuel rails
- Custom intake, catch can and overflow
- 2L Accusump
Management and cooling
- Haltech Elite 2500 ECU
- Haltech iC-7 dash
- Custom body loom, pre-terminated harness
- FIA-approved master kill switch
- VL RB30 radiator, 16" Spal fan, 30-row oil cooler
- Oil and fuel lines and fittings from Zoo Performance
Driveline
- Exedy 790Nm HD clutch
- T56 gearbox built with carbon synchros, Rip Shift
- 1000hp-rated one-piece tailshaft
- Built diff: 31-spline billet axles, full spool, 3.9 ratio
Steering and suspension
- Angry Industries coilovers, 10k front and 8k rear springs
- PC Works S14 knuckles, +30mm S13 lower control arms
- GKTech caster arms, RB Factory caster brackets
- Garage7 extended rack ends, reconditioned R33 rack
- RB Factory upper trailing arms, reinforced lowers
- Whiteline panhard rod and rear sway bar
Brakes
- R33 GTST brakes all round
- Dual-caliper rear setup
- Central Fab Solutions hydraulic handbrake
- HFM BM57 master cylinder, braided lines
- DBA T3 4000 rotors
Safety and interior
- AGI bolt-in roll cage
- Sparco sprint seats and fire suppression
- Zoo Performance harnesses
- Nardi deep-corn wheel, custom switch panel
- Relocated battery, hand-held extinguisher
Parts we run in the car. Brands here aren't sponsors unless they're listed under Our sponsors above.
Audience
Where you'll be seen

- Instagram@ondoors.motorsport
The shop and the car: build content, fab work and event days.
- Instagram@ondoors.jake
The driver's own account: the wagon, the build and seat time.
- On trackEvents and comps
Sydney Motorsport Park, local drift days and competition rounds, in front of drivers, crews and spectators.
- VideoPosts, reels and YouTube
Your brand in our videos now, and on our YouTube channel once it launches.
Partnership enquiries
Let's talk
Tell us a bit about your brand and what you'd like from a partnership. We'll get back to you to talk it through.
We'd especially like to hear from oil, engine management, tyre, wheel, clutch and car insurance brands, and from suppliers who want to back the shop: materials, tooling, welding gear and consumables.




